Welcome to Inchworm Gear Products from Low Range Off-Road.
For close to 2 decades Inchworm gear has been a market leader in the Toyota Transfercase and Drivetrain Adapters to help you go slow on the trail. In late 2013, Jim Christainsen, the creator and owner of Inchworm Gear merged forces with Low Range Off-Road to continue to build the brand and product line.
Another step in making Low Range Off-Road your One Stop Toyota Shop!
Look to us to make your Toyota Tacoma, FJ Cruiser, 4Runner and Pickup go slow on the trail with Single and Dual Transfer Cases, Dual Transfer Case Adapters, 2WD to 4WD Conversions, Transmission Adapters and more.
This adapter allows 2wd to 4wd conversion of any rear wheel drive Toyota & Lexus automatic 4-speed transmission. Most commonly used on Tacoma PreRunners, (hence the name) this adapter fits any '85 or newer rear wheel drive Toyota or Lexus vehicle with an automatic 4-speed transmission. This adapter replaces the tail housing on these automatics and allows single or double 4wd gear driven transfer cases to be installed. Learn More
The Inchworm Tacoma Transmission Adapter allows a gear driven transfer case to be bolted up to a Tacoma, 4runner, FJ Cruiser, or Tundra transmission. Not only can this adapter be used for double cases, it can also be used to fit earlier (pre-'95) pickups and 4Runners with Tacoma engine/tranny combos, or even to fit a Toyota gear driven transfer case into a Tacoma for a passenger side drop front driveshaft. Learn More
Get them while they’re hot! Inchworm’s shiny billet aluminum shift knobs are for your stock, twin, or triple stick shifters. Stock Tcase and 5speed levers are 12mm x 1.25 thread pitch while twin sticks, triple sticks, and single sealed shifters are 1/2-13 thread pitch. Learn More
The Lefty™ is a gear driven transfer case for a Tacoma, 4Runner, or FJ Cruiser with a left-hand drop front axle. It adapts to stock 5-speed and 6-speed manual transmissions, as well as stock automatics. Learn More
This adapter will work to connect almost ANY Toyota flange and Toyota drive shaft!! It will even work as a drive shaft spacer for all patterns except the 95' and older CV's. This adapter does not work with the early 8mm bolt patterns, but works with all later 10mm bolt patterns. The aluminum sleeve pictured on the right fits in the center of the adapter from either side and allows installation of the adapter in either direction. Learn More
Toyota installed gear driven transfer cases in 4 cylinder pickups and 4Runners from 1979 through 1995. Speed sensors were not used as standard equipment in these rigs until about 1992. Speed sensors from chain driven t-cases don't fit gear driven t-cases. This means that swapping out a chain driven case in favor of a gear driven unit, in a 1992 or newer Toyota, will require a speed sensor. Learn More
Somebody said it couldn't be done so Inchworm did it! We are pleased to announce the availability of our Toyota Automatic Transmission Adapter. This adapter will allow you to bolt up a gear driven transfer case (or cases) behind your factory automatic transmission in pre-'95, 4cyl or V6, Toyota 4x4 pickups and 4Runners. Learn More
Attach a gear driven transfer case to your V6 manual transmission with the Inchworm Gear V6 adapter to get the gearing options you want in the rig you’ve got. Also 4 cylinder 4Runners with ADD will need this adapter to install gear driven cases. Adapter allows for 10 degrees of clocking.
* Includes: Adapter Plate
* Oil Seal Extender
* Oil Seal
* Hardware Learn More
These are new dust seals that are usually caked with dirt when you replace the seal. If it is caked with dirt, then it probably has been doing a good job by keeping it away from your transfer case. These are new OEM units from Toyota, so you know they are great quality. Learn More
Toyota Gear Driven Transfer Cases were originally designed for at the most (22RTE Turbo) 101 hp and 173 lb-ft of torque. With the demands of 4.0L FJ, 4Runners and Tacomas pushing 254 hp and 270 lb-ft of Torque, (2UZFE 4.7L V8 at 311 lb-ft) there is greater chances of breakages to the Toyota Gear Driven Components. To get the gear driven Toyota Transfer Case up to the ability to handle serious power- you are in the price range of running something much better...Read on...
The new Clockable Double Case Adapter is the first in a new line of adapters from Inchworm Gear. If you want the best, you have found it. Inchworm Gears products have been known by their quality, strength, and reliability for years.
If you have upgraded to Dana 60 Axles and want to run Toyota Driveshafts or Drivelines, this is the flange you will need.
It is CNC machined from 5140 high strength steel and double drilled to match all of the popular Toyota drive line bolt patterns. This flange will allow you to use your existing Toyota drive lines with a Dana 60 axle.