This New Tcase Cradle is a must for you case if your running lower gears. Not only is is a skid but it grabs on to several extra mounting points to make your case tough as nails. Your transfer case shell is the week point with lower gears and this will make the difference between a bad and

The popular "Mighty Kong." made by Trail Tough  This is combination transfer case mount, bucket and skid plate made for the Suzuki Samurai. With its one piece design it will not flex or distort and actually adds strength to your case. It provides protection where you need it - not where you don't and weighs only 12 lbs. It

Take a thrashin' and keep on bashin'. These bars made by Trail Tough provide superior off-road protection not only for the bottom of the rocker panel but the sides of the vehicle as well. Comes with both bars and all hardware needed.

Introducing the "Rock Barz." This heavy duty steel bar protects from wheel well to wheel well and includes polyurethane end caps. Powder coated black. The Rock Barz can also come sporting an aluminum diamond plate non-skid entry step as shown in picture, black powder coated diamond plate non-skid entry step or you can order your with no step. This product is definitely built to last!

These 3" tube bars made by Calmini offer side rocker panel protection, good looks and functionality. Nurf can be used as a step into the Samurai as well. Designed to run with 30" or smaller tires. Rubbing will occur with larger tires unless the front axle is moved forward. Kit comes complete with two nurf bars, hardware and installation instructions.

These heavy duty 2"x2"x3/16" square tubing rocker bars made by Calmini are built to take a beating on the trail! They feature fully welded and smoothed end caps for a clean look and heavy duty gusseted frame mounts. A Samurai used in any kind of hard core off-road situation will see a caved in rocker panel. This fixes that! Complete

These all new Calmini built formed rocker panel skids for the Samurai are the new standard for off-road rocker protection. These custom formed skids are stronger than individual rocker panels or rocker bars as they protect the entire side, not just underneath as well. Installation is bolt-on with minor drilling required to strengthen the unit. Complete kit comes with two

The new Rock Biters for Samurai side panels are the ultimate in protection. They are made with 1/4" cold rolled flat plate steel that is CNC punched for close tolerances then folded on a 100 ton press. Heavily welded at the exterior seams. The Rock Biters are a one piece side design and made to be the strongest rail ever designed. They look sharp

Easily bolts-on to factory location and provides MAXIMUM under-body protection! Made from laser-cut 3/16” steel, then bent and welded for a clean look. Comes ready to paint.

These diffguards are not your ordinary pipe cap. Laser cut and formed from one piece of 3/16" steel. Design allows for easy cleaning of packed mud with open lower corners, as well as allowing easy installation and removal of the fill plug. Made to fit either your Samurai Axles or those with Toyota axles. Weld on kit. Sold individually.

These Caps made by Trail Tough are bullet proof protection for your diffs without decreasing ground clearance. Designed to fit your stock Samurai housing front or rear and also fits the Samurai/ Sidekick hybrid housings. Comes with 2 caps.

The new Crabs for Samurai are a great design. They are made with 1/4" cold rolled steel folded on a 100 ton press to take any abuse you put them through. Laser cut for close tolerances. They were designed to allow openings for stock E-brake cables, brackets and brake lines. Weld-on.

Protect your investment! This heavy duty skid plate covers the underbody of your Samurai from frame rail to frame rail. It completely covers the transfer case and rear half of the transmission. Installation is easy with four "J" hanger bolts (included). Easily removed for transmission and transfer case servicing. Comes Zinc Coated.

This steel belly pan is tough and allows your Zuk to slip over the big rocks without hanging up or damaging your frame, exhaust or vital components. The positive mounting design eliminates any J-bolt or thread damage. It simply slides up each side of the frame rail and you slide a bolt in over top of the frame. No welding of drilling! Made by Trail Tough

The windshield Support Bra for Samauri Softop windshield frames. Finally a one piece bracket that supports everything, windshield wiper braces, light brackets and doorless mirror brackets all in a one piece design. Each kit comes with self tapping screws for a quick install. Made of .120" steel and powdercoated with a "silver vein finish".

Take a look at your windshield frame, at the passenger wiper, do you see a crack forming, its not to late, get our braces ASAP and prevent having to buy a new windshield frame. Laser cut from 18 Gauge #8 stainless steel. Included is stainless hardware, 3m adhesive backing , 3/32" drill bit, and instructions. Available in Black Powder coat by special request. Kit comes with both sides and is available for both the Soft and Hardtops.

If you are ready to do a spring over conversion on a Suzuki Samurai you should consider strengthening the front axle to accommodate the added performance and adventure you will likely subject your Samurai to. Unlike other Suzuki Samurai gusset kits, stiffening only the center of the axle tube and limiting its ability to absorb and deflect, causing the ends

Axle trusses will help prevent the dreaded sag, so prone to lifted and over worked Suzuki Samurai axles. Constructed of 1/8th inch steel, formed and laser cut, with the Suzuki "S" logo. No grinding or fitting is needed, just hold on and weld. Because the Samurai axle is a bit thinner, you can install one on top as well as the bottom.