This 2 Pin Spanner Wrench is a must when needing to adjust your ICON Coil-over Shocks. The Two Pin deisgn makes it easier to adjust no matter how much room you have to insert the wrench. Learn More

ICON Vehicle Dynamics prides themselves in the highest quality components available. These Billet Aluminum Upper Control Arms are a great addtion to any aftermarket coil-over shock system. Learn More

This 3 Leaf Progressive Add a Leaf Kit comes complete with U-bolts and Center pins for an easy install. This add a leaf kit will give your Tacoma 1.5" of lift after installation. Just remove the factory overload and say good bye to that rough factory ride. Learn More

These adjustable coil-over shocks have proven their strength and longevity for years on end and they keep going. These shocks offer the best ride quality and handling. Learn More

For heavy, fully-outfitted expedition vehicles and those hauling heavy loads, we recommend Emu Dakar heavy duty leaf springs. These springs feature a heavier spring rate than the All-Pro leafs, plus several other features designed to withstand heavier loads. PRICED INDIVIDUALLY, SOLD IN PAIRS Learn More

Improve your Tacoma's suspension performance and gain lift for tire clearance and long travel with All-Pro quality leaf springs! The 2005+ Tacoma 3" lift springs mount in the original spring hangers. PRICED IN PAIRS, SOLD IN PAIRS Learn More

These are the bushings needed for the CS047R Old Man Emu Leaf springs for the 2005+ Toyota Tacoma. Learn More

These Aluminum Sway Bar Relocation Blocks will move your sway Bar 1" forward to avoid any contact with any aftermarket shock. This small investment can save yourself a ton of headache when installing any aftermarket Coil-over Shock. Learn More

SOLD IN PAIRS Learn More

For vehicles with ARB or similar style bumper and accessories adding weight past 110lbs, such as a winch and bumper. SOLD IN PAIRS Learn More

Learn More

Need New Ubolts for your new OME springs? Look no further, we have what you need to make the installation a breeze. Learn More

The 5100 Series offers traditional Bilstein technology. These utilize the stock O.E.M. mounting configuration. 0-1" Rear Lift Learn More

When you are hitting the brakes on your Toyota Tacoma, Hilux, 4Runner or Sequoia and there almost seems like someone is hitting you in the rear it most likely is the cause of the drive line or drive shaft splines not lubricated.

This is the best lubricant on the market for driveshaft slip yokes. It has a PTFE base, usually known as Teflon, most of which you see in heim joints or rod ends for great wear-ability. PTFE is also used in high friction applications because it does not easily get washed off when hit with water. 

Learn More

Tacoma's run out of factory adjustment when you install lift kits. With our patent pending design this upper control arm provides an additional +/- 2 degree of camber and 0 degree to +4 degree of caster change. Built with an OE style ball joint and bushings, this arm is designed to correct alignment angles while maintaining factory ride quality. The hybrid tubular and forged steel design is tough enough to race - on or off-road. These remove and replace arms are available in pairs for lifted and off-road applications or individual left and right arms if just one corner needs adjustment. Learn More

Tacoma's have a center carrier bearing that has to be spaced down when installing rear leaf springs taller than 1". This is when the OME drivshaft spacers are needed, called the "Fitment Kit" FK29. Learn More

These are not just add a leafs, they are specifically designed for the CS047R Rear Old Man Emu leaf springs. These Added to the pack raise the spring 15mm, and increase rate. 2 leafs are included. Learn More

Old Man Emu suspension systems have always focused on ride quality rather than ride height and this new line of shock absorbers includes some of the latest shock valving technology achieving a whole new level of ride quality Learn More

Our Blocks are CNC Cut and Machined from solid 6061-T6 Billet Aluminum, with a CNC Machined Pressed in steel locating stud. By our machining and press technique, we achieve what cannot be matched in todays market- ACCURACY. Fits: 2005-2011 Toyota Tacoma 4WD, Base Model, TRD, TIX, and Prerunner Models. (All 4WD Models) Learn More