3/8” CNC laser cut caliper brackets, Larger GM style calipers-shipped fully loaded, GM style vented rotors-custom made just for this application. Learn More

Another one of those cool products you wish you had invented. These speed bleeders replace your OEM brake bleeder valve. With these installed brake bleeding is finally a one person operation. Simply crack open the bleeder and press on the brake pedal. When the pedal is release, a check valve inside the bleeder prevents air from entering the brake lines. Learn More

Great quality brake lines at a lower cost!  Specs mimic to 5 Layer ones above but not available in different colors.  These steel braided brake lines are 26" long and are DOT approved. Front lines use factory mounting clips so there is no need to modify the factory clips in any way. Learn More

There is a common problem with the 1989-1995 Toyota Hilux Pickup Truck and 4Runner... the clutch bracket breaks, leaving you stranded. If yours has started developing cracks from a lot of usage, then it most likely is on its way out. Replace your unit with a new OEM Toyota unit that has been updated to provide many more years of trouble free usage. Learn More

Low Range Off Road is is now offering semi-metallic replacement brake pads for the Trail-Gear pickup, 4Runner, and Tacoma rear disc brake kits. Learn More

Has your Toyota brake pedal or clutch pedal pads seen better days? If they have worn to the pedal, you may be running the risk of slipping off the brake or the clutch. This is not a good situation to be in. These are easily replaceable, slip off the old one and slip on the new one. Learn More

Looking for a brake line tee for the rear of your Toyota or Suzuki Rear Axle?  We have new brake line tees that are made out of steel and then zinc plated.

This is the ideal fitting for legally joining 3 tubes together. Also features a 10mm mounting hole for secure installation.

 

Fits: Toyota and Suzuki Models with M10-1.0 Thread (Most Models)

Learn More

Makes a great replacement for older Pickup's and 4Runners with smaller bore size. Fits 1979-1995 Pickups and 4Runners. Master Cylinder features 1" piston and residual valves for both front and rear disc brakes. Can be used with disc or drum brakes. Includes reservoir. Learn More

These calipers are the larger V6 style found on 88-95 Pickups and 4Runners. Great replacement for worn our or leaking calipers. Also makes a great upgrade on 79-85 solid front axles when used with vented rotors listed below. Note wheel spacers may be needed to clear calipers on some wheels. No core charge, outright purchase. Brake pads are not included with calipers. Learn More

Premium Semi-Metallic asbestos free front replacement brake pads. Set of 4 pads. Applications to fit Toyota's from 1979-2004

Learn More

1986 and later pickups and 4Runner feature larger vented rotors from the factory. Earlier 1979-1985 trucks used solid (non vented) rotors up front along with smaller calipers. If your installing a solid front axle on an 86 and later rig you will want to install a set of these vented rotors onto the axle. With these rotors you will be Learn More

This is a great disc brake conversion kit for use on Toyota 79-95 rear axles. Comes with brackets and all needed hardware for a clean install. This kit requires the use of two Toyota front early brake rotors (83-85) and two Toyota front early brake calipers (79-85) that are not included. Made by Trail-tough

Learn More

Here is an answer to your stopping woes, a disk brake conversion! Each bracket is constructed of laser cut one piece 3/8” thick steel for utter strength and simplicity. Years of the calipers are 79-85 Monte Carlo or Cadilac Eldorado, front or rear depending on if you want to install an ebrake or not. (rear has ebrake setup) One small Learn More

These line locks have unsurpassed holding power which guarantees to keep you from rolling at any angle. Check out the features and you will see what sets it apart from the rest. Including the price on the best selling Line lock on the market!

Learn More

This hydraulic lock uses the line pressure of the system to hold your brake locked, no electrical or special linkage required. Just step on the foot brake, push the park lock down, let off the foot brake and its locked. Step on the foot brake again and it opens automatically. Holds any vehicle with hydraulic brakes where you put it. Learn More

For pulling and installing wheels during a brake job this is the right tool for the job. 13/16" on one end and 3/4" on the other. Thin wall design fits better than standard sockets. This socket is rated for use with an impact gun. 1/2" drive. Learn More

Factory Toyota Brake Hardware Learn More

The brake backing plates can be a bother on front Toyota solid axles. They often get bent from trail damage and small rocks can get trapped between the backing plate and the rotor causing noise and damage. For many years we have taken the stock brake backing plate and cut out the center section. Then we would reassemble the axle Learn More

Normally the nuts that hold the wheel bearings can be reused over and over again. If your wheel bearing retainer nuts need replacing this kit is for you. Kit contains 2 nuts, star washer and flat index washer. Fits: 79-85 Toyota Hilux Pickup Truck and 4Runner Solid Axles Learn More